Keymark Alarm Accessories

Accessories to complement our Alarm Systems

PIR Detector
PIR Detector

The PIR Wireless Detector is a wall mount passive infrared wireless detector suitable for Wireless installations at any decor.

• Coverage 15mx15m (50’x50’)
• Intelligent Digital Signal Processing
• Bracket installation
• Wall tamper suitable for corners
• Includes two 3V long-life lithium batteries
• Available in one-way wireless models with single battery

 

Universal Transmitter
PIR Detector

The Universal Transmitter is a supervised, general-purpose transmitter that can be connected to door and window magnetic contacts or to other sensors.

• Frequency of 868MHz
• Range (Line of Sight) 400m (1300ft)
• Enables wireless operation of any NO or NC contact detector
• Internal read contact and external magnet
• Can be used with shock sensors
• Selectable response time
• Pulse count model for shutter protection
• Sends alarm and restore signals, preventing panel arming when the zone is in state of alarm
• Cover and back tamper
• Low battery and transmission LED indication
• Test mode for installation testing
• Uses one of 16 million codes without dipswitches
• Fully supervised – transmits status signal every 65 minutes
• Includes 3V lithium battery with for 5-year battery life

 

Wireless Smoke Detector
PIR Detector

The Wireless Smoke Detector is a photoelectric smoke detector for adding fire warning capability to intruder alarm systems. The smoke detector is designed for use in a single residential unit only. When sufficient smoke is detected, the detector will sound its alarm horn and the transmitter will send an alarm message

• Frequency of 868MHz
• Range up to 300m (1000ft) line of sight
• Ceiling mount
• No radiation emission
• Restore transmission
• Test mode
• Low battery transmission
• Uses one of 16 million codes without dipswitches
• Status transmission every 15/65 minutes
• Cover and back tampers
• Uses a 9 volt lithium or alkaline battery

 

Wireless Glass Protection
PIR Detector

The glass sensor provides on alarm in case of Breaking glass.

• Protects all glass types: plate, tempered, laminated and wired
• Dual frequency pattern recognition
• 9m range with Omni-directional microphone
• Full remote testing
• Optional swivel bracket
• Cover and back tamper
• Includes long-life 3V lithium battery


 

Wireless Flood Detector
PIR Detector

The Wireless Flood Detector provides an alarm in case of flooding above the sensor level.

• Digital Microprocessor with Intelligent Digital Signal Processing
• 2.5m cable between flood sensor and wireless transmitter
• Includes 3V long life lithium battery
• Fully supervised
• Cover & Back Tamper protection
• 868MHz

 

Wireless CO Detector
PIR Detector

The Wireless CO Detector is a supervised and fully battery powered transmitter that is effective for detecting build up carbon monoxide (CO).  Upon detecting the CO gas, the unit emits an alarm and notifies the control panel.

• Monitoring of carbon monoxide in a continuous manner
• Loud alarm (85 dB) and signal to the panel when detecting a build up of   carbon
• monoxide
• Test button and continuous self-testing function.
• Designed to meet the requirements of UL Standard 2034
• Includes 2 x 3V lithium batteries with 3 year typical lifetime

 

Universal GSM/GPRS Module
PIR Detector

Advanced GSM/GPRS Module (AGM) Universal version in metal box
GSM Line Simulation
Encrypted SMS and GPRS reporting to ARC’s
Supports Prepaid SIM cards
Programming via SMS or PC software (local or remote)

 

4-Button Keyfob
PIR Detector

4-function miniature transmitter
The 4-Button Keyfob is a miniature transmitter. It has 4 functions, activated upon 3 channels (each channel has a different address): arm & disarm on the same channel, panic and utility output on the other two channels.

• Frequency of 868MHz
• Range (Line of Sight) 200m (650ft)
• Pocket size for key ring or pendant mounting
• Low battery and transmission LED indication
• Uses one of 16 million codes without dipswitches
• Includes lithium battery for 3-year battery life

 

Wireless Wristband Panic Transmitter

PIR Detector

The Wristband Panic Transmitter is a stylish single button transmitter used to signal a panic alarm in the event of distress.  This water-resistant panic transmitter can be worn either on the wrist or as a pendant, and is ideal for the elderly or disabled who might not be able to reach the phone in the event of an emergency.

• Low battery and transmission LED indication
• Includes wristband and necklace cord
• Water resistant IP67 rating
• Includes lithium battery with a 3-year typical lifetime

 

External Sounders
PIR Detector

The external sounder includes a pre-alarm feature that begins at entry delay countdown and sends an alarm if  vandalized during entry delay. Battery life economy is ensured through an advanced algorithm, and a low battery signal is included for both transceiver and sounder.

• Two-way wireless,  External sounder
• 105dBA piezo sound output, adjustable volume
• Low-voltage long-life LED strobe
• Adjustable strobe time and flash rate

 

Wireless WatchOUT

PIR Detector

The Wireless WatchOUT is the Wireless version of the award winning WatchOUT detector. It has identical detection features to the WatchOUT PIR, with the addition of Active IR for Anti-mask, making it the only wireless outdoor detector with antimasking capability. Two long-life lithium batteries are included

·  Digital Correlation Technology
·  Pet friendly for animals up to 70cm head height (2’4”)
·  Wide range of swivels for wall, pole, or barrier applications
·  Active IR Anti-mask 
·  IP65 environmental rating
·  Hood - provides protection

 

2 Way Wireless Key Pad
PIR Detector

Stylish 2-Way Wireless Keypad enables full installer programming
 

• Fully wireless installer programming and end-user operation
• Blue LCD and backlight
• Proximity tag for Arm/Disarm
• Simplified menu logic – displays only relevant menus  - according to hardware configuration, accessories installed and authorization level
• Includes 3 x CR123A long-life lithium batteries

 

2 Way 8 Button keyfob with LED

The 2 way remote control is used to arm, disarm and perform other system operations. You can select to use a pin code prior to activation, for higher security, Communication with the base unit is bi-directional so you can query the system status and receive indication of the alarm status via the remote control LED.   

• Pin Code for higher security
• System status request & LED display
• Includes long-life 3V lithium battery
 

 

GSM Module

Advanced GSM/GPRS Module
GSM Line Simulation
Encrypted SMS and GPRS reporting to ARC’s
Supports most SIM cards
Programming via SMS or PC software (local or remote)
 

• Installs neatly inside mk2 main control panel
• Contacts you via mobile phone sim card 
• Eliminates phone lines been compromised